How to Install a Bath Tub
How to Install a Bath Tub
Blog Article
They are making several great annotation about Tools You Need to Install a New Bathtub overall in this article beneath.
Installing a tub isn't exactly brain surgery, but it does call for solid plumbing, woodworking, as well as occasionally, tiling abilities. Replacing an old bath tub with a new one is also a reasonably challenging project. If the old bathtub is easily obtainable, the job can move easily; if you have to open up a wall to eliminate the old bathtub and place the new bath tub, the task is a lot harder. In either situation, the task is within a house handyman's abilities, although you will certainly need an assistant to move out the old bathtub and also set in the brand-new one. Make sure you have actually certified yourself for the work and fit trying it. Instead of working with a professional to take over a halfway-completed task, it is better to think about using one before you start. Opportunities are you may need a specialist plumber to make tube connections.
This short article will certainly help you set up a new bathtub in your washroom if you have actually already gotten a new tub and also don't need to change the setup of your previous water supply pipelines.
Your devices and material list should make up the following:
Removing Old Taps
If you need to replace old faucets with new ones as a part of your setup, after that the first thing you should do is separate the water supply. After doing so, turn on the taps to drain pipes any water staying in the system. The process of getting rid of the existing taps can be quite problematic because of the limited access that is frequently the situation.
Make use of a container wrench (crowsfoot spanner) or a tap tool to reverse the nut that attaches the supply pipes to the taps. Have a fabric prepared for the staying water that will certainly originate from the pipelines. When the supply pipelines have actually been gotten rid of, use the same tool to loosen the nut that holds the taps onto the bath/basin. You will certainly need to quit the solitary faucets from transforming throughout this procedure. As soon as the faucets have actually been eliminated, the holes in the bath/basin will certainly need to be cleansed of any kind of old securing substance.
Prior to going on to fit the brand-new faucets, contrast the pipeline connections on the old taps to the brand-new faucets. If the old faucets are longer than the brand-new faucets, then a shank adapter is required for the new taps to fit.
Fitting New Touches
If the tails of the new faucets are plastic, after that you will certainly require a plastic connector to stop damages to the string. One end of the adapter fits on the plastic tail of the faucet as well as the various other end supplies a link to the existing supply pipes.
If you need to fit a monobloc, then you will require decreasing couplers, which connects the 10mm pipe of the monobloc to the standard 15mm supply pipe.
Next off, place the faucet in the placing opening in the bath/basin making sure that the washing machines remain in location between the tap and the sink. Secure the faucet in place with the manufacturer given backnut. When the tap is securely in position, the supply pipes can be attached to the tails of the taps. The taps can either be attached by using corrugated copper piping or with normal faucet connectors. The previous kind ought to be connected to the faucet ends first, tightening up only by hand. The supply pipelines can later on be connected to the various other end. Tighten up both ends with a spanner after both ends have been linked.
Mounting the Tub
Using the two wood boards under its feet, place the bath tub in the needed position. The wood boards are helpful in uniformly spreading the weight of the tub over the area of the boards rather than concentrating all the weight onto four little points.
The next objective is to guarantee that the bath tub is leveled all round. This can be achieved by inspecting the level and adjusting the feet on the tub till the spirit level checks out degree.
To install faucets, fit the bottom of the furthest adaptable tap connector to the proper supply pipeline by making a compression join; after that do the very same for the other faucet.
Activate the water supply as well as examine all joints and brand-new pipework for leakages and tighten them if needed. Fill up the tub as well as additionally check the overflow electrical outlet and also the normal outlet for leakages.
Ultimately, fix the bath paneling as explained in the maker's user's manual. Tiling as well as securing around the bath tub needs to wait until the tub has actually been made use of a minimum of when as this will settle it into its final setting.
Planning for the Installation
Firstly, the supporting framework provided with the bathroom needs to be fitted (if required) according to the manufacturer's directions. Next, fit the taps or mixer to the bathtub. When fitting the tap block, it is very important to see to it that if the faucet features a plastic washing machine, it is fitted between the bath and the taps. On a plastic bath, it is likewise practical to fit a sustaining plate under the faucets system to avoid stress on the tub.
Fit the versatile faucet ports to the bottom of the two taps using 2 nuts and also olives (occasionally provided with the bathtub). Fit the plug-hole electrical outlet by smearing mastic filler round the sink outlet hole, and then pass the electrical outlet via the hole in the bath. Use the nut provided by the supplier to fit the plug-hole. Take a look at the plug-hole outlet for an inlet on the side for the overflow pipe.
Next off, fit the end of the flexible overflow pipe to the overflow electrical outlet. Afterwards, screw the pipe to the overflow face which ought to be fitted inside the bathroom. See to it you utilize all of the supplied washing machines.
Connect the catch to the bottom of the waste electrical outlet on the bathtub by winding the string of the waste outlet with silicone mastic or PTFE tape, and screw on the catch to the electrical outlet. Link the bottom of the overflow tube in a comparable manner.The bath need to currently prepare to be suited its final placement.
Tiling Around the Tub
In the area where the bath fulfills the tile, it is essential to secure the joins with a silicone rubber caulking. This is necessary as the fitting can relocate sufficient to fracture a rigid seal, triggering the water to penetrate the wall surface between the bath and also the tiling, causing problems with wetness as well as possible leakages to the ceiling below.
You can choose from a selection of coloured sealants to assimilate your fixtures and also installations. They are offered in tubes and also cartridges, and also can sealing voids approximately a size of 3mm (1/8 inch). If you have a larger gap to load, you can load it with twists of soaked newspaper or soft rope. Remember to constantly fill the bathtub with water prior to securing, to permit the motion experienced when the tub is in usage. The sealer can split relatively early if you do not consider this movement before sealing.
Conversely, ceramic coving or quadrant floor tiles can be made use of to border the bathroom or shower tray. Plastic strips of coving, which are easy to use as well as cut to size, are additionally conveniently readily available on the market. It is a good idea to fit the ceramic tiles utilizing water-resistant or water-proof glue and also cement.
How to Install or Replace a Bathtub
Find Your Dimensions
The first step in any bathtub installation or replacement is to select the right size tub for your bathroom. Start by measuring your existing bathtub’s alcove from wall to wall. The standard size for bathtubs is around 5 feet long and 30 or 32 inches wide. Purchase the size that’s closest to your previous tub.
After you’ve measured, you’ll need to figure out what type of tub you need. Face the alcove. If the drain is on the right-hand side, you’ll need a right drain tub. If it’s on the left, get a left drain tub. Easy enough, right?
Disconnect the Water Supply and Drain Assembly
Before you can start on your removal, make sure that you turn off the tub’s water supply. Some bathrooms have a shutoff valve, but if you don’t see one, you’ll need to turn off the supply at your house’s water main. Once the water’s off, open the valves to release any remaining air in the supply lines.
Then, disconnect the tub drain flange. This process varies based on the type of drain you have, but in most cases, you’ll need a drain flange removal tool to perform this task. If you’re feeling handy, you might be able to use a pair of needle-nose pliers to twist and pull the flange.
Now comes the fun part. In order to disconnect the drain assembly, you’ll need to be able to get to the space underneath the tub. You might need to access the tub drain from a crawlspace or a basement. Don’t forget to take a pipe wrench with you, as you’ll need it to loosen the pipe at the connection.
Cut Out the Old Tub
After removing the drainpipe assembly, you can take out the old bathtub. Cut a strip above the tub edge in the wall surrounding the bathtub that's about 6 inches in height. The tools you need here may vary depending on the type of wall surround you have in the alcove. If you’re cutting drywall, use a drywall saw and remove the section of the wall all the way down to the studs. If you have tile, you’ll need to use a grinder with a diamond blade to cut through the grout line. Then, use a chisel to remove the individual tiles. Take care here not to cut through any studs.
Find the tub flange. Remove the screws that attach the flange to the studs in the wall. At this point, the tub should be freed from the wall.
Once you’ve removed the flange, use a utility knife to cut away the caulk between the tub and the floor. When this is done, you should be able to lift the tub up and out of the alcove. Keep in mind that, depending on what it’s made of, the old tub could be tremendously heavy. You should plan to have a friend help you move it just in case.
Install the New Tub
Before you make any adjustments to the area, place the new tub in the alcove to make sure it fits properly and that the tub drain lines up with the P-trap underneath the floor.
Remove it and install a 2 x 4 ledger board. Measure the tub’s flange, then mark that height on the wall. Screw the ledger board to studs in the wall. This will help to support the weight of the tub.
Once the ledger board has been installed, go ahead and secure the drain to the tub. For this step, you’ll need some plumber’s putty. Roll a small amount of putty in your hands and wrap it around the underside of the drain flange. Push the drain into the tub from underneath the tub.
When the drain has been attached, connect the overflow drain. To do this, you’ll place the gasket on the overflow elbow and move it behind the tub. Once that’s on, connect the overflow pipe and the drainpipe, but take care not to overtighten.
Secure the Tub
After the connections are in, it’s time to set the tub in place. Before you start, make sure the flange lines up with the markings you made in Step 4. Because the ledger board holds the tub in place, it’s important that it matches up. If not, you’ll need to remove it and readjust.
Once your measurements line up, attach the flange to the studs on all three sides of the wall. Please note that you should not screw the flange to the wall. Instead, you should use roofing nails because they won’t rust over time. When the tub is in place, install the baseboard and the molding in front of and around the tub.
Repair and finish off the drywall or tile that you cut in Step 3. If you’re installing a fiberglass bath surround, now’s the time to adhere it to the alcove.
Then, enjoy your tub! While all these steps might seem intimidating, removing and installing a new bathtub is a relatively easy DIY project that can be completed in a single day. And now, when you settle in for your next bubbly soak, you can enjoy your bath without the distraction of a tub in disrepair.
https://www.homeserve.com/en-us/blog/how-to/bathtub-replacement/
Do you like reading up on A Step-by-Step Guide to Installing a Bathtub? Give a remark down below. We would be pleased to find out your ideas about this write up. Hoping that you come back again in the near future. Liked our entry? Please share it. Help another person find it. Thanks so much for taking the time to read it.
Order Repair Report this page